Best Screws for Particle Board: A Guide for DIY Enthusiasts

We all know that working with a particle board can be a pain in the butt because of the fact they easily break when drilled. So, what’s a guy have to do? Find the best screws for particle board, of course! Then again, most of the time, this is easier said than done because there are lots of factors to consider to find out which screw would work best. This is not a case of trial-and-error too.

Right before you drill that first hole into that particle board, you should already be more than equipped with the right screws. This is so as to avoid wasting a valuable piece of wood material. After all, you don’t want to cut and cut until you have no board left to work with, do you?

In this article, we are going to provide you with a detailed comparison of three of our top three go-to screws for particle boards. Before we do that, though, let us first tell you of the things that you need to know before you put in your screws. After all, how you go about drilling the particle board also plays a great role in making sure that your project is done successfully.

Drilling Holes into a Particle Board

Having the best screws for particle boards is not enough to ensure the success of your project. You should also be mindful of many other things. Here are some tips on what you should do before putting in your chosen screws.

  • The initial hole should be at least 85% of the diameter of the screw.
  • The hole should be deeper compared to the screw length.
  • Screws that are placed at the edge should be, at the very least, place at 2.5 inches from the end.
  • Screws that will be put on the face should be more than an inch from the edge.
  • Never over-tighten the screws as it might crack the wood.
  • Start with a small hole then build it up gradually to fit the screw.

Confident in your drilling skills? Itching to find out which makes and models are considered the best screws to use on particle board? Then, read on!

Best Screws for Particle Board: The Top Three Contenders

Below, we will provide you with the top three screws we use when working with particle board. Each one offers their own set of features, pros, and cons. By the end of this article, we hope that you get to find which one would work best for your project’s specific needs.

The Rok Hardware Standard Thread Phillips Pan Head Screws

 

The name says it all. This screw features a pan-type head with a #2 Phillips drive. It is categorized as having a #6 diameter and ½-inch length. It is made of metal with a zinc finish and can be bought in 100s or 1000s.

The Rok Hardware Standard Thread Phillips boasts a good holding power for not just particle boards but also plastic composites and medium-density fiberboard (MDF).

Pros

  • Easily drills through wood
  • Can be used for drills and screwdrivers
  • Holds a strong bond between two pieces of wood

Cons

  • Can be too small
  • Can rust easily
  • Might be hard to remove once it is secured

The Kreg SML-C250-250 Coarse Washer-Head Pocket Hole Screws

 

At first glance, it is quite noticeable that this screw has a larger thread than the other screws featured in this article, which means it offers maximum power for the hold. It features a #8 drive and a 2.5-inch length, making it great to use on materials that are quite soft such as plywood, pin, melamine, MDF, and particle board.

The washer head at the bottom helps the screen from pulling through the wood. It can be used both indoors and outdoors, and its metal body means that it can also be used on hardwood. One pack contains 250 pieces of self-tapping, pocket-hole screws.

Pros

  • Has a good grip
  • Easy to work with
  • Quicker to screw things together
  • Cuts through a hole themselves
  • Durable
  • Can withstand pressure
  • Does not strip
  • Default size can be used on a lot of wood pairings

Cons

  • Might be too sharp
  • Inconsistency in the quality of the tabs
  • The outdoor version can be slightly better than the indoor ones
  • The packaging is a bit faulty

The Bolt Dropper Stainless Flat Head Phillips Wood Screw

 

These screws are coated with black Xylan. This makes it resistant to any corrosions, so it will be able to serve its purpose longer. Additionally, it can be used in a composite material, wood, and even in wet environments. Further, it has a Philips drive that is deep cut.

Lastly, we have the Bolt Dropper Stainless Flat-Head Phillips Wood Screws. These screws are coated with black Xylan, which makes it resistant to any corrosions and allows it to serve its purpose longer. It can be used to hold together composite materials and wood. In fact, it can even be used in wet environments.

Additionally, these screws also have a #8 hard-to-strip, deep-cut Phillips drive and is an inch long. It has a flat-type head with a type A point type. It is sold in 100-piece packs and comes with a lifetime guarantee.

Pros

  • Has well-formed heads
  • Has clean threads
  • Good to look at
  • Easy to screw in
  • No stripping

Cons

  • The hold is not that strong
  • Threads may not be deep enough
  • The coating comes off after a time
  • Size is not accurate
  • Can be too sharp

The Verdict

Looking at all the features, as well as the pros and cons of each product, we have concluded that the best particle board screws that are worth investing in are the Kreg SML-C250-250 Coarse Washer-Head Pocket Hole Screws. Why so? For many reasons, actually.

For one, it is the only screw in this list that will not only securely hold your boards together but also are not going to give you a headache in screwing them in. In fact, you won’t even have to drill holes into your board before-hand. Its design and makeup are enough to drill them straight into the wood.

With that said, you will be done with your work in no time. And the best part? You won’t even have to break a sweat. Now, that is time, money, and energy well-spent, don’t you think?

Click Here to Leave a Comment Below 0 comments

Leave a Reply: